Question Bank DSP (ECE-2006)

By

Click on the Link below

Question Bank DSP

Comments

  1. Surbhi Singh12/01/2018 4:13 pm

    ow it is really wonderful and awesome thus it is very much useful for me to understand many concepts and helped me a lot. it is really explainable very well and i got more information from your blog.
    Home Tutors in Lucknow | Home Tuition Service

    ReplyDelete
  2. Megan Valish12/24/2018 2:24 pm

    You are writing some Amazing tips. This article really helped me a lot. Thanks for sharing this blog.
    AliExpress Electronics Coupons

    ReplyDelete

Post a Comment

Popular posts from this blog

Lattice Ladder Structure - (ECE-2006)

By
Image
SYLLABUS (This Document contains Module 7) Module:1 Frequency Analysis of Signals and Systems-1: Review of Discrete -Time Signals and Systems – Classification, Convolution- Z- transform: ROCstability/ causality analysis, DTFT: Frequency response-System analysis. Module:2 Frequency Analysis of Signals and Systems-2: Frequency domain sampling- Sampling rate conversion- Aperiodic correlation estimation-Cepstrum processing- Band limited discrete time signals- Phase and group delay- DFT-Properties. Frequency analysis of signals using DFT-FFT Algorithm-Radix-2 FFT algorithms-Applications of FFT Module:3 Theory and Design of Analog Filters: Design techniques for analog low pass filter -Butterworth and Chebyshev approximations, frequency transformation, Properties -Constant group delay and zero phase filters Module:4 Design of IIR Digital Filters: IIR filter design: IIR filter Design - Bilinear and Impulse Invariant Techniques- Spectral transformation of Digital filters...
Keep reading

MICRO LAB EXAMPLES - (ECE3003)

By
Program 1. Write and assemble a program to add the following data and then use the simulator to examine the CY flag. Code: ORG 0000H MOV A,#92H MOV R0,#23H ADD A,R0 JNC L1 INC R7 L1: MOV R1,#66H ADD A,R1 JNC L2 INC R7 L2: MOV R2,#87H ADD A,R2 JNC L3 INC R7 L3: MOV R3,#0F5H ADD A,R3 JNC L4 INC R7 L4: END Program 2. Write and assemble a program to load the values into each register R0-R4 and then push each of these registers onto the stack. Single Step program and examine the stack and the SP register after execution of each instruction. Code: ORG 0000H MOV R0,#25H MOV R1,#35H MOV R2,#45H MOV R3,#55H MOV R4,#65H PUSH 0 PUSH 1 PUSH 2 PUSH 3 PUSH 4 END Program 3. Add the following subroutine to the previous program, single step through the subroutine and examine the RAM locations. After data has been transferred from ROM space into RAM, the subroutine should copy the data from RAM locations starting at 40H to ROM locations starting at 60H. Code: ORG 0000H MOV DPTR,#200H MOV R0,#...
Keep reading

Line Coding PSD - (ECE-4001)

By
Image
SYLLABUS (This Document contains Module 3)  Module:1 Sampling & Quantization: Model of digital communication system – Review of sampling – Quantization – Uniform & non-uniform quantization. Module:2 Waveform Coding Techniques:  Pulse Code Modulation – Quantization noise and signal to quantization noise ratio – Companding (A law and μ law) - Delta modulation. Module:3 Line Codes: Representation of Line Codes – Properties and applications of Line codes – Power Spectral Density of NRZ unipolar, NRZ Polar, NRZ Bipolar and Manchester. Module:4 Baseband System: Inter Symbol Interference – Nyquist criterion for distortion less transmission – Raised cosine spectrum – Correlative coding – Eye pattern – Equalization. Module:5 Bandpass System-I: Gram-Schmidt orthogonalization procedure – Correlation Receiver – QAM- Generation and Detection of Coherent system (BASK, BFSK, BPSK, QPSK, MSK) – Error performance. Module:6 Bandpass System-II: Matche...
Keep reading